700 MINIMUM REQUIREMENTS FOR SAMPLING MATERIALS
Spec No. |
Material |
Material only Inspection or Sampling Requirements |
Post Inspection Instructions |
|
203
|
Embankment |
Assure 203.02 Q and R materials conform to the individual material requirements. Sample materials when requested by the Engineer.
Follow S 1015 for acceptance
Soil Embankment: 50 lb (23 kg) Granular Embankment: 50 lb (23 kg) |
™ |
|
258 |
Dowel Bar Retrofit |
Silicone Sealant– Obtain letter of certification stating that the material meets the requirements of item 258. Material to be shipped from manufacturer not more than 9 months prior to use. Dowel Bar grout - Verify brand name of material is on QPL at the time of use. |
|
|
301 302 |
Asphalt Concrete Base |
Project: Visually inspect delivered loads and newly placed mat
Plant: Test 1 sample in 4 days for verification. Observe other contractor QC sample and QC test 1 in 4 days. Plant: Conduct minimum monitoring requirements. |
Project: Contact project Engineer/ DCE/DET immediately if problems are seen
Plant: Compare results per 403. Report on monitoring. |
|
305
|
PC Concrete Pavement |
Make two 6"x6"x4' beams for every 7500 yd² (6500 m²) or fraction thereof daily. Field test beams for required load for the specification. Report results in CMS (Trns.port SiteManager ™ ). |
Core samples taken every 2000 sq. yds by Contractor. Conform to S 1064 |
|
307 |
Non Stabilized Drainage Base |
Provide samples conforming to 703.12 for design verification. Provide in process samples as directed by the Engineer. Sample material conforming to 703.12 |
Determine locations for thickness tolerance checks according to S 1064. |
|
308 |
Asphalt Treated Free Draining Base |
Provide a JMF to the Lab for approval. Include 1 gal (4 L) sample of asphalt and 70 lb (32 kg) sample of aggregate |
Determine locations for thickness tolerance checks according to S 1064. |
|
409 |
Sawing and Sealing Asphalt Concrete pavement Joints |
Assure backer rod is on QPL at the time of use. Inspect material for condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District testing and OMM |
|
421 |
Micro Surfacing |
Project: Conduct a test strip per 421.09, inspect per 421.10 and accept per 421.11. |
|
|
422 |
Chip Seal with Polymer Binder |
Project: Conduct a test strip per 422.05. Clean the surface per 422.06. Verify binder and aggregate application per 422.07 and 422.08. Ensure contractor quality control per 422.10. Verify all of 422.11 is met for acceptance. |
|
|
423 |
Fibers for Asphalt Concrete: Polyester Propylene Polypropylene |
Verify type and brand name of material is on QPL at the time of use. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use submit a use a 1 quart sample to the Laboratory. |
|
424 |
Asphalt Concrete (Fine Graded Polymer) |
For Type A see 301,302 procedures. For Type B see 448 procedures. |
|
|
442
|
Asphalt Concrete
|
Project and Plant: See requirements for 446 or 448 as specified for the 442 item. |
|
|
443 |
Asphalt Concrete (Stone Mastic) |
See 446 requirements. |
|
|
446 |
Asphalt Concrete |
Project: Visually inspect delivered loads and newly placed mat Project: Obtain daily mix sample for District test unless otherwise directed by the DET. Project: Obtain 10 cores for each lot (day) within 48 hours for District test. Locate cores for sampling. Project: See 702.04 or 702.13 for tack sample. Plant: Conduct minimum monitoring requirements. Plant: See 702.01 for PG binder sample |
Project: Contact project Engineer/ monitoring team immediately if problems seen. Project: Observe proper handling and quick delivery of the mix sample. Place cores in box flat side down, do not stack boxes, do not leave in weather, deliver to lab promptly. Plant: Report on monitoring. |
|
448 |
Asphalt Concrete |
Project: Visually inspect delivered loads and newly placed mat Project: Give lot sample location to the District monitoring team unless otherwise directed by the DET. Project: See 702.04 or 702.13 for tack sample. Project: Conduct density gauge QA per S 1055 Plant: Conduct minimum monitoring requirements. Plant: See 702.01 for PG binder sample |
Project: Contact project Engineer/monitoring team immediately if problems seen. Project: Re Core for S 1055 if gauge change or JMF change. Plant: Report on monitoring. |
|
451
|
PC Concrete Pavement |
Make 6"x6"x4' beams for every 7500 yd² (6500 m²) or fraction thereof daily. Make two beams if testing before 7 days. Field test beams for required load for the specification. Report results in CMS (Trns.port SiteManager ™). |
Core samples taken every 2000 sq. yds by Contractor. Conform to S 1064 |
|
451.08.B |
Dowel Bond Breaking Material |
Check new light form oil by labels on new cans. No sampling required |
Report material as not approved and follow policy for non specification materials |
|
452 |
PC Concrete Pavement |
Make 6"x6"x4' beams for every 7500 yd² (6500 m²) or fraction thereof daily. Make two beams if testing before 7 days. Field test beams for required load for the specification. Report results in CMS (Trns.port SiteManager ™). |
Core samples taken every 2000 sq. yds by Contractor. Conform to S 1064 |
|
499.02 |
Water |
Potable water is satisfactory. If question about water quality, obtain 1 gallon sample. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if water appears to contain sewage, oil, acid, or other matter. |
|
503.09
|
Excavation for Structures Backfill |
Sampled only when requested by the Engineer per Section 203 Soil Embankment: 50 lb (23 kg) Granular Embankment: 50 lb (23 kg) |
|
|
504 |
Sheet Piling Left in Place |
Use 711.03 materials |
|
|
507.03 |
Bearing Piles Steel Pile Points |
Only use points from suppliers on the approved list incorporated into the project plans. Document in CMS (Trns.port SiteManager ™) as needed. |
Notify District Testing if material non-performs or looks defective during use. Notify the contractor with non-compliance issues. |
|
509.08 |
Reinforcing Steel - Plastic support chairs |
Assure plastic supports conform to 709.15. |
Maximum spacing of supports in slabs, beams and girders to be 4 feet; or less to prevent substantial deflection. |
|
511 |
Concrete for Structures |
Make two 6"x12" cylinders for spans over 20 ft each day, each 200 yd³. For spans 20 ft span and under, make two 6"x12" cylinders each 50 yd³ or less. Document in CMS (Trns.port SiteManager ™). Field or Standard Cure according to ACI/ODOT specifications. |
Within 24 to 48 hours after sampling, ship cylinders to Laboratory with required documentation. |
|
515 |
Prestressed Concrete Bridge Members |
Assure products are supplied by a source on the Certified List for S-1079 maintained by OMM. Received with TE-24. Check dimension and condition Document in CMS (Trns.port SiteManager ™). |
If rejecting material because material non-performs or looks defective during use, notify District Testing and OMM, Cement and Concrete section, |
|
515.15 |
Prestressed Concrete Bridge Members -Corrosion Inhibitors |
Verify company and brand name of material is on QPL at the time of use. Document in CMS (Trns.port SiteManager ™). |
For Precast beams delivered on TE-24, verification performed by OMM. |
|
526 |
Approach Slabs |
Make 6"x12" cylinders for each day, each 200 yd³. Document in CMS (Trns.port SiteManager ™). Make two beams if testing before 7 days. Field or Standard Cure according to ACI/ODOT specifications. |
Within 24 to 48 hours after sampling, ship cylinders to Laboratory with required documentation. |
|
601.12 |
Tied Concrete Block Mats (Slope/Channel Protection) |
Verify company and brand name of material is on QPL at the time of use. Ensure proper type and inspect material for condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use submit a representative qty of defective material to the Laboratory. |
|
603.02 |
External Sealing Bands Joint Wrap |
Verify company and brand name of material is on QPL at the time of use. Inspect material for condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use submit a representative qty of defective material to the OMM. |
|
609.02 |
Curbing, Concrete Medians, and Traffic Islands - Stone Curbs |
Contact District Testing and OMM Aggregate Section to assure stone curb conforms to requirements of 609.02 |
|
|
610
|
Cellular Retaining Walls |
610.04.A Cellular Products will be supplied by a source on the Certified Lists for S-1073 maintained by OMM. Received with TE-24. Check dimension, condition and compliance with approved drawings. 610.04.B Cellular Products accept by certified test data documentation at the Project . Document in CMS (Trns.port SiteManager ™).
|
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
613 |
Low Strength Mortar Backfill |
Supplier to perform trial batches of 1 cy to ensure flowable consistency and yield. Refer to Item 613.05 for alternate mix design. Alternate mix designs will be submitted for approval 30 days prior to placement.. Submit written permission form to EPA 10 days prior to placement. |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
632.11 |
Traffic Signal Equipment Loop Detector Sealant |
Verify manufacturer is on QPL. Inspect for condition, appearance and package markings. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
633 |
Traffic Signal Controllers |
Inspect material for condition and conformance to shop drawings. Manufacturer’s certified test data required for acceptance. Refer to Handbook of Procedures for Contractor Certification of Lighting, Signing & Traffic Signal Working Drawings on OMM Manual website. |
Notify District Testing if rejecting material.
|
|
653.02
|
Topsoil |
Obtain one (1) pint sample of material from each source and/or stockpile of visually different material from same source. Use friction top, air tight metal container supplied by the Department. Submit to Office of Geotechnical Engineering Operations. Samples will include a TE-31 form or CMS (Trns.port SiteManager ™) print screen |
|
|
657.02 |
RipRap for Tree Protection |
Confirm with DET that the aggregate source has a acceptable performance history. For sources with poor performance require test data conforming to ASTM D5240 |
|
|
658.02 |
Tree Root Aeration - Aggregate |
Assure source on the Certified List for S 1069 maintained by OMM Assure aggregate meets soundness requirements. Sample sources with no soundness history and obtain a 100 lb (45 kg) sample |
|
|
659.03 |
Seeding and Mulching - Liming Materials |
Only accept materials from suppliers licensed in Ohio. See OMM website for list of Ohio Department of Agriculture list of licensed suppliers. Document in CMS (Trns.port SiteManager ™) |
|
|
659.04 |
Seeding and Mulching - Commercial Fertilizer
|
Only accept materials from suppliers licensed in Ohio. See OMM website for list of Ohio Department of Agriculture list of licensed suppliers. Inspect material for certified analysis and condition. Non-standard application rate require approval prior to use Document in CMS (Trns.port SiteManager ™). |
Licensing is required. Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing & OMM. |
|
659.07 659.08 659.09 S1022 |
Seeding and Mulching Seeds Legumes Native Grasses and Wildflowers
|
Verify manufacturer is on certified supplier List maintained by OMM. Received with TE-24 and description bill of lading. Document in CMS (Trns.port SiteManager ™). |
Verify District approval of seed mixture. |
|
659.14 659.15 659.16 |
Seeding and Mulching - Mulch |
Material should be reasonably free from foreign matter that would inhibit seed germination.
|
Notify District if rejecting material. |
|
660.02 |
Sodding |
Verify company and brand name of material is on QPL at the time of use. Certification required for each shipment. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material.
|
|
661 |
Planting Trees Shrubs and Vines [Trees] [Shrubs] [Vines] |
Verify company and brand name of material is on QPL at the time of use. Inspect material for condition. Plant material should be sealed until use. Document in CMS (Trns.port SiteManager ™). |
Final acceptance should take place after period of establishment. Notify District Testing if rejecting material.
|
|
STANDARD MATERIALS SPECIFICATIONS
|
||||
701.01 701.02 701.04 701.05 701.07 701.09 |
Cement, Hydraulic ASTM Types I, IA, II, III Masonry Type IS(<25) |
Verify manufacturer on Concrete Plant Batch Ticket is on Certified List for S 1028 maintained by OMM. Verify material against bill of lading description. Document in CMS (Trns.port SiteManager ™). |
Obtain one ½ gallon sample and original bill-of-lading per concrete plant every 180 days for QA. Ship sample to OMM laboratory. Ensure that sample container is filled to capacity prior to transport.
|
|
701.10 |
Micro-Silica |
Verify manufacturer on Concrete Plant Batch Ticket is on Certified List for S 1045 maintained by OMM. Verify material against bill of lading description Document in CMS (Trns.port SiteManager ™). |
Obtain one ½ gallon sample and original bill-of-lading per concrete plant every 180 days for QA. Ship sample to OMM laboratory. Ensure that sample container is filled to capacity prior to transport. |
|
701.11 |
Ground Granulated Blast Furnace (GGBF) Slag |
Verify manufacturer on Concrete Plant Batch Ticket is on Certified List for S 1034 maintained by OMM. Verify material against bill of lading description Document in CMS (Trns.port SiteManager ™). |
Obtain one ½ gallon sample and original bill-of-lading per concrete plant every 180 days for QA. Ship sample to OMM laboratory. Ensure that sample container is filled to capacity prior to transport.
|
|
701.13 |
Fly Ash |
Verify manufacturer on Concrete Plant Batch Ticket is on Certified List for S 1026 maintained by OMM. Verify material against bill of lading description Document in CMS (Trns.port SiteManager ™). If high LOI fly ash verify manufacturer on Concrete Plant Batch Ticket is on List for S 1115. |
Obtain one ½ gallon sample and original bill-of-lading per concrete plant every 180 days for QA. Ship sample to OMM laboratory. Ensure that sample container is filled to capacity prior to transport.
|
|
702.01 |
Asphalt Binder |
Certified asphalt PG binder: As directed by the Lab. Plant: Minimum of one sample per project per season, except for inconsequential quantities.
Non-Certified PG binder: Will be sampled and approved by the Department before use. |
Certified binder: Plant: Submit sample to Lab.
Non-certified binder: Submit to Lab. Do not allow asphalt production until material is approved. |
|
702.02 702.03 702.04 702.07 702.13 |
Cut Back Asphalt Cut Back Asphalt Emulsions Emulsified Asphalts Asphalt Emulsion MWS Rubberized Asphalt Emulsion |
Certified material: At the refinery or source as directed by the Lab. Project and/ or Plant: Min. one sample per each 25,000 gallons. None for less than 300 gallons.
Non-certified material: Will be sampled and approved by the Department before use. |
Certified material: Submit to Lab.
Non-certified material: Submit to Lab. Do not use until approved by Lab. |
|
702.05 702.06 |
Asphalt Primer Waterproofing Asphalt Waterproofing |
Each batch sampled and pre-approved per TE 24. Lab contacted by supplier for test. |
Project: Do not accept on project without TE 24. |
|
702.14 |
Rubber Compound |
Certified test data |
|
|
702.16 |
Polymer Emulsified Binder |
Certified test data |
|
|
702.17 |
Crack Sealant |
Material is pre-tested and approved. Will be shipped with TE-24. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use Notify District Testing and OMM Asphalt Section. |
|
703.02 703.04 703.05 703.08 |
Coarse Aggregate from Certified Stock |
Coarse Aggregate will be supplied by a Pre-Qualified producer/supplier (S1069). Verify the producer/supplier is Pre-Qualified using the Pre-Qualified Producer/Supplier list maintained by OMM (website). Document in CMS. |
60 to 75 lb. QC sample taken by District lab at source a minimum four (4) times per year. No project sampling required except if project believes there is a problem with the material [either gradation or quality] |
|
703.02 703.04 703.05 703.08
|
Coarse Aggregate from Non-Certified Stock |
Coarse Aggregate will be supplied by a Pre-Qualified producer/supplier (S1069). Verify the producer/supplier is Pre-Qualified using the Pre-Qualified Producer/Supplier list maintained by OMM (website).60 to 70 lb. QC sample taken from each 2600 ton (2360 metric ton) stockpile, submitted to OMM Aggregate Section. 100 lb QC sample for sizes 1,2, and 24. Document in CMS. Do not use until tested and approved. |
No additional project sampling required for approved, sampled tonnage except if project believes there is a problem with the material [either gradation or quality] |
|
|
|
|
|
|
703.02 703.03 703.04 703.05 703.06 703.10 |
Fine Aggregate from Certified Stock |
Fine Aggregate will be supplied by a supplier on the Pre-Qualified Supplier List for S 1069 maintained by OMM. Document in CMS (Trns.port SiteManager ™). |
30 to 40 lb. QC sample taken by District lab at source a minimum four (4) times per year. No project sampling required except if project believes there is a problem with the material [either gradation or quality] |
|
703.02 703.03 703.04 703.05 703.06 703.10 |
Fine Aggregate from Non-Certified Stock |
Fine Aggregate will be supplied by a supplier on the Pre-Qualified Supplier List for S 1069 maintained by OMM. 30 to 40 lb. QC sample taken from each 1800 ton (1640 metric ton) stockpile, submitted to OMM Aggregate Section. Document in CMS (Trns.port SiteManager ™). Do not use until tested and approved. |
No additional project sampling required for approved, sampled tonnage except if project believes there is a problem with the material [either gradation or quality]
|
|
|
|
|
|
|
703.02 703.04 703.05 |
Dense Graded Aggregate from Certified Stock |
Dense Graded Aggregate will be supplied by a supplier on the Pre-Qualified Supplier List for S 1069 maintained by OMM. Document in CMS (Trns.port SiteManager ™). |
90 to 100 lb. QC sample taken by District lab at source a minimum four (4) times per year. No project sampling required except if project believes there is a problem with the material [either gradation or quality] |
|
703.02 703.04 703.05 |
Dense Graded Aggregate from Non-Certified Stock |
Dense Graded Aggregate will be supplied by a supplier on the Pre-Qualified Supplier List for S 1069 maintained by OMM. 90 to 100 lb. QC sample taken from each 5200 ton (4720 metric ton) stockpile, submitted to OMM Aggregate Section. Document in CMS (Trns.port SiteManager ™). Do not use until tested and approved. |
No additional project sampling required for approved, sampled tonnage except if project believes there is a problem with the material [either gradation or quality] |
|
703.07 |
Materials Mineral filler |
For limestone dust assure from a source on Certified List for S 1069. For Portland cement assure source is on Certified list for S 1028 For inert mineral filler sample for gradation. Submit to District Lab. |
|
|
703.11 Type 1 |
Structural Backfill for 603 Bedding and Backfill from Certified Stock |
Assure materials provided by a supplier on the Pre-Qualified Supplier List for S 1069 maintained by OMM. Document in CMS (Trns.port SiteManager ™). |
90 to 100 lb. QC sample taken by District lab at source a minimum four (4) times per year. No project sampling required except if project believes there is a problem with the material [either gradation or quality] |
|
703.11 Type 1 |
Structural Backfill for 603 Bedding and Backfill from Non-Certified Stock |
Assure materials provided by a supplier on the Pre-Qualified Supplier List for S 1069 maintained by OMM. 90 to 100 lb. QC sample taken from each 5200 ton (4720 metric ton) stockpile, submitted to OMM Aggregate Section. Document in CMS (Trns.port SiteManager ™). Do not use until tested and approved. |
No additional project sampling required for approved, sampled tonnage except if project believes there is a problem with the material [either gradation or quality] |
|
703.11 Type 2 |
Structural Backfill for 603 Bedding and Backfill from Certified Stock |
Assure materials provided by a supplier on the Pre-Qualified Supplier List for S 1069 maintained by OMM. Document in CMS (Trns.port SiteManager ™). |
90 to 100 lb. QC sample taken by District lab at source a minimum four (4) times per year. No project sampling required except if project believes there is a problem with the material [either gradation or quality] |
|
703.11 Type2 |
Structural Backfill for 603 Bedding and Backfill from Non-Certified Stock |
Assure materials provided by a supplier on the Pre-Qualified Supplier List for S 1069 maintained by OMM. 90 to 100 lb. QC sample taken from 5200 ton (4720 metric ton) stockpile, submitted to OMM Aggregate Section. Document in CMS (Trns.port SiteManager ™). Do not use until tested and approved. |
No additional project sampling required for approved, sampled tonnage except if project believes there is a problem with the material [either gradation or quality] |
|
703.11 Type 3 |
Structural Backfill for 603 Bedding and Backfill from Certified Stock |
Assure materials provided by a supplier on the Pre-Qualified Supplier List for S 1069 maintained by OMM. Document in CMS (Trns.port SiteManager ™). |
60 to 70 lb. QC sample taken by District lab at source a minimum four (4) times per year. No project sampling required except if project believes there is a problem with the material [either gradation or quality] |
|
703.11 Type 3 |
Structural Backfill for 603 Bedding and Backfill from Non-Certified Stock |
Assure materials provided by a supplier on the Pre-Qualified Supplier List for S 1069 maintained by OMM. 60 to 70 lb. QC sample taken from each 5200 ton (4720 metric ton) stockpile, submitted to OMM Aggregate Section. Document in CMS (Trns.port SiteManager ™). Do not use until tested and approved. |
No additional project sampling required for approved, sampled tonnage except if project believes there is a problem with the material [either gradation or quality] |
|
|
|
|
|
|
703.13 |
Coarse Aggregate for Items 451 and 452 |
Assure materials provided by a supplier on the Pre-Qualified Supplier List for S 1069 maintained by OMM. Assure materials are on the OMM Freeze Thaw List Follow requirements of coarse aggregate 703.02 Document in CMS (Trns.port SiteManager ™). |
No project sampling required except if project believes there is a problem with the material [either gradation or quality] |
|
703.14 |
Steel Slag Aggregate for Non-Pavement Use |
Assure materials from a supplier on the Pre-Qualified Supplier List for S 1069 maintained by OMM. Stockpile and sample each 2500 tons (2300 metric tons). Notify the District laboratory for inspection of sources and to obtain split samples. Test for expansion |
No additional project sampling required for approved, sampled tonnage except if project believes there is a problem with the material [either gradation or quality] |
|
|
|
|
|
|
703.16 |
Suitable Materials for Embankment Construction |
Multiple materials listed. Follow the requirements of the individual material specification |
Follow the requirements of the individual material specification |
|
|
Modification required for 703.16 |
|
|
|
|
|
|
|
|
703.17 |
Dense Graded Aggregate for Item 304 from Certified Stock |
Products will be supplied by a supplier on the Pre-Qualified Supplier List for S 1069 maintained by OMM. Document in CMS (Trns.port SiteManager ™). |
90 to 100 lb. QC sample taken by District lab at source a minimum four (2) times per year. No project sampling required except if project believes there is a problem with the material [either gradation or quality] |
|
703.17 |
Dense Graded Aggregate for Item 304 from Non-Certified Stock |
Products will be supplied by a supplier on the Pre-Qualified Supplier List for S 1069 maintained by OMM. 90 to 100 lb. QC sample taken from each 5200 ton (4720 metric ton) stockpile, submitted to OMM Aggregate Section. Document in CMS (Trns.port SiteManager ™). Do not use until tested and approved. |
No additional project sampling required for approved, sampled tonnage except if project believes there is a problem with the material [either gradation or quality] |
|
|
|
|
|
|
703.18 |
Aggregate for Items 410, 411, and 617from Certified Stock |
Products will be supplied by a supplier on the Pre-Qualified Supplier List for S 1069 maintained by OMM. Document in CMS (Trns.port SiteManager ™). |
90 to 100 lb. QC sample taken by District lab at source a minimum four (4) times per year. No project sampling required except if project believes there is a problem with the material [either gradation or quality] |
|
703.18 |
Aggregate for Items 410, 411, and 617from Non-Certified Stock |
Products will be supplied by a supplier on the Pre-Qualified Supplier List for S 1069 maintained by OMM. 90 to 100 lb. QC sample taken from each 5200 ton (4720 metric ton) stockpile, submitted to OMM Aggregate Section. Document in CMS (Trns.port SiteManager ™).. Do not use until tested and approved. |
No additional project sampling required for approved, sampled tonnage except if project believes there is a problem with the material [either gradation or quality] |
|
703.19.A |
Crushed Aggregate Slope Protection and Filter Aggregate for Dump Rock Fill |
Products will be supplied by a supplier on the Pre-Qualified Supplier List for S 1069 maintained by OMM. Document in CMS (Trns.port SiteManager ™). |
No sampling required except if project believes there is a problem with the material [either gradation or quality]
|
|
703.19.B |
Dumped Rock Fill and Rock Channel Protection |
Products will be supplied by a supplier on the Pre-Qualified Supplier List for S 1069 maintained by OMM. Confirm with OMM laboratory source has know durability history Sample on direction of the OMM laboratory Document in CMS (Trns.port SiteManager ™). |
No sampling required except if project believes there is a problem with the material [either gradation or quality]
|
|
704.01 704.02 704.03 |
Block: Brick Concrete Masonry Shale |
Verify type of material is on QPL at the time of use. Inspect for condition and defects. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. When material non-performs or looks defective during use reject material and sample 12 brick representative of defect to OMM for QA follow-up. |
|
705.01 |
Fiber Reinforced Polymer (FRP) Dowel Bars |
Certified test data from an accredited testing facility will accompany each shipment. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing upon receipt of shipment. |
|
705.03 |
Joint Filler Preformed |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, appearance and dimension. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use send one (1) 1.5'x2.5' sample representative of defect to OMM for QA follow-up. |
|
705.04 |
Joint and Crack Sealer Hot Applied
|
Material is pre-tested and approved. Will be shipped with TE-24. Document in CMS (Trns.port SiteManager ™).
|
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM Asphalt Section for sampling requirements. |
|
705.05 |
Burlap Cloth Materials |
Inspect for condition, appearance and dimension. Documenting in CMS (Trns.port SiteManager ™ ) .is not required Only sample if there if questioning material meet specification |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
705.06 |
Sheet Curing Materials |
Inspect for condition, appearance and dimension. Documenting in CMS (Trns.port SiteManager ™ ) is not required. Only sample if there if questioning material meet specification |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
705.07 |
Concrete Curing Compounds |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition and appearance. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use send one (1) quart sample representative of defect to OMM, Cement and Concrete section, for QA follow-up. |
|
705.10 |
Air Entraining Admixtures |
Verify type and brand name of material listed on Concrete Plant Batch Ticket is on QPL at the time of use. Document in CMS (Trns.port SiteManager ™). |
Storage: Admixtures should be stored at concrete producer in such a manner to permit easy access for proper identification in weather resistant units. Provide minimum QA sample of one (1) every 180 days per concrete plant, each material, each company. Minimum sample size one (1) quart |
|
705.11 |
Joint Sealer Preformed Elastomeric |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, appearance, dimension and manufacturer trademark. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material because material non-performs or looks defective during use. |
|
705.12 |
Chemical Admixtures for Concrete |
Verify type and brand name of material is on QPL at the time of use. Document in CMS (Trns.port SiteManager ™). |
Storage: Admixtures should be stored at concrete producer in such a manner to permit easy access for proper identification in weather resistant units. Provide minimum QA sample of one (1) every 180 days per concrete plant, each material, each company. Minimum sample size one (1) quart.
|
|
705.15 |
High Molecular Weight Methacrylate (HMWM) |
Verify type and brand name of material is on QPL at the time of use. Document in CMS (Trns.port SiteManager ™). |
|
|
705.20 |
Non Shrink, Non Metallic Grout |
Verify type and brand name of material is on QPL at the time of use. Ensure mixing is performed in accordance with manufacturer’s recommendations on the container. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM for sampling requirements. |
|
705.21 |
Quick Setting Concrete Mortar |
Verify type and brand name of material is on QPL at the time of use. Ensure mixing is performed in accordance with manufacturer’s recommendations on the container. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM for sampling requirements. |
|
705.22 |
Non-shrink Mortar |
Verify manufacturer is on the Approved List maintained by OMM. Ensure mixing is performed in accordance with manufacturer’s recommendations on the container. Make three (3) or more 3"x6" cylinders from keyway mix. Ship to OMM Concrete Section. Document in CMS (Trns.port SiteManager ™). |
Sample will be tested at 3, 7 and 28 days. Do not open structure to traffic until a compressive strength of 5000 psi (34.5 MPa) is achieved. |
|
705.23 A |
Epoxy-urethane Sealers |
Verify type and brand name of material is on QPL at the time of use. Ensure mixing is performed in accordance with manufacturer’s recommendations on the container. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use obtain 1 qt (1 L) samples in a sealed container and send to OMM. |
|
705.23 B |
Non Epoxy Sealers |
Verify type and brand name of material is on QPL at the time of use. Ensure mixing is performed in accordance with manufacturer’s recommendations on the container. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use obtain 1 qt (1 L) samples in a sealed container and send to OMM. |
|
705.24 |
Soluble Reactive Silicate |
Verify type and brand name of material is on QPL at the time of use. Ensure mixing is performed in accordance with manufacturer’s recommendations on the container. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material.
|
|
705.25 |
Gravity Fed Resin |
Verify type and brand name of material is on QPL at the time of use. Ensure mixing is performed in accordance with manufacturer’s recommendations on the container. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use obtain 1 qt (1 L) samples in a sealed container and send to OMM. |
|
705.26 |
Epoxy injection Resin |
Verify type and brand name of material is on QPL at the time of use. Make sure that ports are properly installed and ensure mixing is performed in accordance with manufacturer’s recommendations Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material.
|
|
706.01 |
Non-Reinforced Concrete Pipe |
Assure products are supplied by a source on the Certified List for S-1074 maintained by OMM. Received with TE-24. Check dimension, markings, roughness or excessive cracks. Document in CMS (Trns.port SiteManager ™). |
If rejecting material because material non-performs or looks defective during use, notify District Testing and OMM , Cement and Concrete section, |
|
706.02 |
Reinforced Concrete Circular Pipe |
Assure products are supplied by a source on the Certified List for S-1074 maintained by OMM. Received with TE-24. Check dimension, markings, roughness or excessive cracks. Document in CMS (Trns.port SiteManager ™). |
If rejecting material because material non-performs or looks defective during use, notify District Testing and OMM , Cement and Concrete section, |
|
706.03 |
Reinforced Concrete Pipe, Epoxy Coated |
Assure products are supplied by a source on the Certified List for S-1074 maintained by OMM. Received with TE-24. Check dimension, markings, roughness or excessive cracks. Document in CMS (Trns.port SiteManager ™). |
If rejecting material because material non-performs or looks defective during use, notify District Testing and OMM , Cement and Concrete section, |
|
706.04 |
Reinforced Concrete Elliptical Culvert, Storm Drain and Sewer Pipe |
Assure products are supplied by a source on the Certified List for S-1074 maintained by OMM. Received with TE-24. Check dimension, markings, roughness or excessive cracks. Document in CMS (Trns.port SiteManager ™). |
If rejecting material because material non-performs or looks defective during use, notify District Testing and OMM , Cement and Concrete section, |
|
706.05 |
Precast Reinforced Concrete Box Sections |
Assure products are supplied by a source on the Certified List for S-1073 maintained by OMM. Received with TE-24. Check dimension, markings, roughness or excessive cracks. Document in CMS (Trns.port SiteManager ™). |
If rejecting material because material non-performs or looks defective during use, notify District Testing and OMM , Cement and Concrete section, |
|
706.051 |
Precast Reinforced Concrete Three-Sided Flat Topped Culverts |
Assure products are supplied by a source on the Certified List for S-1073 maintained by OMM. Received with TE-24. Check dimension, markings, roughness or excessive cracks. Document in CMS (Trns.port SiteManager ™). |
If rejecting material because material non-performs or looks defective during use, notify District Testing and OMM , Cement and Concrete section, |
|
706.052 |
Precast Reinforced Concrete Arch Sections |
Assure products are supplied by a source on the Certified List for S-1073 maintained by OMM. Received with TE-24. Check dimension, markings, roughness or excessive cracks. Document in CMS (Trns.port SiteManager ™). |
If rejecting material because material non-performs or looks defective during use, notify District Testing and OMM , Cement and Concrete section, |
|
706.06 |
Perforated Concrete Pipe |
Assure products are supplied by a source on the Certified List for S-1074 maintained by OMM. Received with TE-24. Check dimension, markings, roughness or excessive cracks. Document in CMS (Trns.port SiteManager ™). |
If rejecting material because material non-performs or looks defective during use, notify District Testing and OMM , Cement and Concrete section, |
|
706.07 |
Concrete Drain Tile |
Assure products are supplied by a source on the Certified List for S-1074 maintained by OMM. Received with TE-24. Check dimension, markings, roughness or excessive cracks. Document in CMS (Trns.port SiteManager ™). |
If rejecting material because material non-performs or looks defective during use, notify District Testing and OMM , Cement and Concrete section, |
|
706.08 |
Vitrified Clay Pipe |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, appearance and dimension. Document in CMS (Trns.port SiteManager ™). |
If rejecting material because material non-performs or looks defective during use, notify District Testing and OMM , Cement and Concrete section, |
|
706.09 |
Clay Drain Tile |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, appearance and dimension. Document in CMS (Trns.port SiteManager ™). |
If rejecting material because material non-performs or looks defective during use, notify District Testing and OMM , Cement and Concrete section, |
|
706.10 |
Bituminous pipe joint filler |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, appearance and dimension. Document in CMS (Trns.port SiteManager ™). |
If rejecting material because material non-performs or looks defective during use, notify District Testing and OMM , Asphalt Concrete section, |
|
706.11 |
Resilient and Flexible Gasket Joints |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, appearance and dimension. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, Structural Metals and Welding section, if rejecting material because material non-performs or looks defective during use. |
|
706.12 |
Resilient and Flexible Joints |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, appearance and dimension. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM Structural Metals and Welding section, if rejecting material because material non-performs or looks defective during use. |
|
706.13 |
Precast Reinforced Concrete Manhole Riser Sections, Catch Basins and Inlet Tops, and Temporary Barriers |
Assure products are supplied by a source on the Certified List for S-1073 maintained by OMM Received with TE-24. Check dimension, markings, roughness or excessive cracks. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM , Cement and Concrete section, if rejecting material because material non-performs or looks defective during use. |
|
706.14 |
Flexible Plastic Gaskets |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, appearance and dimension. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, Structural Metals and Welding section, if rejecting material because material non-performs or looks defective during use. |
|
706.15 |
Precast Reinforced Concrete Outlets |
Assure products are supplied by a source on the Certified List for S-1073 maintained by OMM Received with TE-24. Check dimension, markings, roughness or excessive cracks. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM , Cement and Concrete section, if rejecting material because material non-performs or looks defective during use. |
|
707.01 |
Metallic Coated Corrugated Steel Conduits and Underdrains [½ inch and 1/4 depth corrugations] |
Products will be supplied by a source on the Certified List for S-1019 maintained by OMM. Received with TE-24. Check dimensions and markings. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. |
|
707.02 |
Metallic Coated Corrugated Steel Conduits [1 inch depth corrugation] |
Products will be supplied by a source on the Certified List for S-1019 maintained by OMM. Received with TE-24. Check dimensions and markings. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. |
|
707.03 |
Structural Plate Corrugated Steel Structures |
Products will be supplied by a source on the Certified List for S-1019 maintained by OMM. Received with TE-24. Check dimensions and markings. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. |
|
707.04 |
Precoated, Galvanized Steel Culverts |
Products will be supplied by a source on the Certified List for S-1019 maintained by OMM. Received with TE-24. Check dimensions and cracks. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use |
|
707.05 705.07 |
Bituminous Coated Corrugated Steel Pipe and Arches with Paved Invert [½ inch depth corrugations] [1 inch depth corrugations] |
Products will be supplied by a source on the Certified List for S-1019 maintained by OMM. Received with TE-24. Check dimensions and markings. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. |
|
707.10 |
Steel Tubing Square and Rectangular |
Generally a fabricated component received with TE-24. Check dimensions and markings. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. |
|
707.11 |
Mortar Lined Corrugated Steel Pipe [any corrugation depth] |
Products will be supplied by a source on the Certified List for S-1019 maintained by OMM. Received with TE-24. Check dimensions and markings. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. |
|
707.12 |
Corrugated Steel Spiral Rib Conduits |
Products will be supplied by a source on the Certified List for S-1019 maintained by OMM. Received with TE-24. Check dimensions and markings. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use |
|
707.13 707.14 |
Bituminous Lined Corrugated Steel Pipe [½ depth corrugations] [1 depth corrugations] |
Products will be supplied by a source on the Certified List for S-1019 maintained by OMM. Received with TE-24. Check dimensions and markings. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. |
|
707.15 |
Corrugated Steel Box Culverts |
Products will be supplied by a source on the Certified List for S-1019 maintained by OMM. Received with TE-24. Check dimensions and markings. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. |
|
707.21 |
Corrugated Aluminum Alloy Conduits and Underdrains [1/4, 7/16 & ½ inch depth corrugations] |
Products will be supplied by a source on the Certified List for S-1019 maintained by OMM. Received with TE-24. Check dimension and markings. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. |
|
707.22 |
Corrugated Aluminum Alloy Conduits |
Products will be supplied by a source on the Certified List for S-1019 maintained by OMM. Received with TE-24. Check dimension and markings. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. |
|
707.23 |
Aluminum Alloy Structural Plate Conduits |
Products will be supplied by a source on the Certified List for S-1019 maintained by OMM. Received with TE-24. Check dimensions and markings. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. |
|
707.24 |
Corrugated Aluminum Spiral Rib Conduits |
Products will be supplied by a source on the Certified List for S-1019 maintained by OMM. Received with TE-24. Check dimensions and markings. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. |
|
707.25 |
Corrugated Aluminum Box Culverts |
Products will be supplied by a source on the Certified List for S-1019 maintained by OMM. Received with TE-24. Check dimensions and markings. Document in CMS (Trns.port SiteManager ™ ). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. |
|
707.31 707.32 707.33 |
Polyethylene Corrugated Pipe |
Products will be supplied by a source on the Certified List for S-1066 maintained by OMM. Received with TE-24. Check dimension and markings. Document in CMS (Trns.port SiteManager ™ ). |
Notify District Testing and OMM, asphalt section, if rejecting material because material non-performs or looks defective during use. |
|
707.41 |
Polyvinyl Chloride Plastic Pipe |
If material is shipped with TE24, accept based on inspection of material for type, condition and dimension. Document in CMS (Trns.port SiteManager ™). If no TE24, accept based on inspection of material for type, condition, dimension, receipt and verification of manufacturer’s certified test data. Document in CMS (Trns.port SiteManager ™) |
Notify District Testing if rejecting material.
|
|
707.42 |
Polyvinyl Chloride Corrugated Smooth Interior Pipe |
If material is shipped with TE24, accept based on inspection of material for type, condition and dimension. Document in CMS (Trns.port SiteManager ™). If no TE24, accept based on inspection of material for type, condition, dimension, receipt and verification of manufacturer’s certified test data. Document in CMS (Trns.port SiteManager ™) |
Notify District Testing if rejecting material.
|
|
707.43 |
Polyvinyl Chloride Profile Wall Pipe |
If material is shipped with TE24, accept based on inspection of material for type, condition and dimension. Document in CMS (Trns.port SiteManager ™). If no TE24, accept based on inspection of material for type, condition, dimension, receipt and verification of manufacturer’s certified test data. Document in CMS (Trns.port SiteManager ™) |
Notify District Testing if rejecting material.
|
|
707.44 |
Polyvinyl Chloride Sanitary Pipe |
If material is shipped with TE24, accept based on inspection of material for type, condition and dimension. Document in CMS (Trns.port SiteManager ™). If no TE24, accept based on inspection of material for type, condition, dimension, receipt and verification of manufacturer’s certified test data. Document in CMS (Trns.port SiteManager ™) |
Notify District Testing if rejecting material.
|
|
707.45 |
Polyvinyl Chloride Solid Wall Pipe |
If material is shipped with TE24, accept based on inspection of material for type, condition and dimension. Document in CMS (Trns.port SiteManager ™). If no TE24, accept based on inspection of material for type, condition, dimension, receipt and verification of manufacturer’s certified test data. Document in CMS (Trns.port SiteManager ™) |
Notify District Testing if rejecting material.
|
|
707.46 |
Polyvinyl Chloride Drain Waste and Vent Pipe |
If material is shipped with TE24, accept based on inspection of material for type, condition and dimension. Document in CMS (Trns.port SiteManager ™). If no TE24, accept based on inspection of material for type, condition, dimension, receipt and verification of manufacturer’s certified test data. Document in CMS (Trns.port SiteManager ™) |
Notify District Testing if rejecting material.
|
|
707.47 |
ABS and Polyvinyl Chloride Composite Pipe |
If material is shipped with TE24, accept based on inspection of material for type, condition and dimension. Document in CMS (Trns.port SiteManager ™). If no TE24, accept based on inspection of material for type, condition, dimension, receipt and verification of manufacturer’s certified test data. Document in CMS (Trns.port SiteManager ™ ) |
Notify District Testing if rejecting material.
|
|
707.51 |
ABS Drain Waste and Vent Pipe |
If material is shipped with TE24, accept based on inspection of material for type, condition and dimension. Document in CMS (Trns.port SiteManager ™). If no TE24, accept based on inspection of material for type, condition, dimension, receipt and verification of manufacturer’s certified test data. Document in CMS (Trns.port SiteManager ™ ) |
Notify District Testing if rejecting material.
|
|
707.52 |
ABS Sewer Pipe |
If material is shipped with TE24, accept based on inspection of material for type, condition and dimension. Document in CMS (Trns.port SiteManager ™). If no TE24, accept based on inspection of material for type, condition, dimension, receipt and verification of manufacturer’s certified test data. Document in CMS (Trns.port SiteManager ™ ) |
Notify District Testing if rejecting material.
|
|
707.70 |
Welded and Seamless Steel Pipe |
Verify type and brand name of material is on QPL at the time of use. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural metals and Welding section, if rejecting material because material non-performs or looks defective during use. |
|
708.01 |
Products will be supplied by a source on the Certified List for S-1084 maintained by OMM. Verify type and brand name of material is on QPL at the time of use. Inspect material container for markings, expiration date and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, chemical section, if rejecting material because material non-performs or looks defective during use. Obtain a 1 qt (1 L) sample representative of the defects. |
||
708.02 708.02B 708.02C 708.02D |
OZEU Structural Steel Pant Organic Zinc Prime Coat Epoxy Intermediate Coat Urethane Finish Coat |
Products will be supplied by a source on the Certified List for S-1084 maintained by OMM. Verify type and brand name of material is on QPL at the time of use. Inspect material container for markings, expiration date and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, chemical section, if rejecting material because material non-performs or looks defective during use. Obtain a 1 qt (1 L) sample representative of the defects. |
|
709.01 |
Deformed and Plain Billet Steel Bars for Concrete Reinforcement |
Products will be supplied by a source on the Certified List for S-1068 maintained by OMM. Received with TE-24. Check dimension, markings and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain three (3) 30" (.8 m) long samples of each rebar size, with markings, and submit for QA testing by the Laboratory. |
|
709.03 |
Rail Steel Deformed and Plain Bars for Concrete Reinforcement |
Products will be supplied by a source on the Certified List for S-1068 maintained by OMM. Received with TE-24. Check dimension, markings and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain three (3) 30" (.8 m) long samples of each rebar size, with markings, and submit for QA testing by the Laboratory. |
|
709.05 |
Axle Steel Deformed and Plain Bars for Concrete Reinforcement |
Products will be supplied by a source on the Certified List for S-1068 maintained by OMM. Received with TE-24. Check dimension, markings and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain three (3) 30" (.8 m) long samples of each rebar size, with markings, and submit for QA testing by the Laboratory. |
|
709.08 |
Cold-Drawn Steel Wire for Concrete Reinforcement |
Products will be supplied by a source on the Certified List for S-1068 maintained by OMM. Received with TE-24. Check dimension, markings and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain three (3) 30" (.8 m) long samples of each diameter and submit for QA testing by the Laboratory. |
|
709.09 |
Fabricated Steel Bar or Rod Mats for Concrete Reinforcement |
Products will be supplied by a source on the Certified List for S-1068 maintained by OMM. Received with TE-24. Check dimension, markings and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain 3 ft x 3 ft (1 m x 1 m) of the mat and submit for QA testing by the Laboratory. |
|
709.10 |
Welded Steel Wire Fabric for Concrete Reinforcement |
Products will be supplied by a source on the Certified List for S-1068 maintained by OMM. Received with TE-24. Check dimension, markings and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain 3 ft x 3 ft (1 m x 1 m) of the mat and submit for QA testing by the Laboratory. |
|
709.11 |
Deformed Steel Wire for Concrete Reinforcement |
Products will be supplied by a source on the Certified List for S-1068 maintained by OMM. Received with TE-24. Check dimension, markings and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain 3 ft x 3 ft (1 m x 1 m) of the mat and submit for QA testing by the Laboratory. |
|
709.12 |
Welded Deformed Steel Wire Fabric for Concrete Reinforcement |
Products will be supplied by a source on the Certified List for S-1068 maintained by OMM. Received with TE-24. Check dimension, markings and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain 3 ft x 3 ft (1 m x 1 m) of the mat and submit for QA testing by the Laboratory. |
|
709.13 |
Coated Dowel Bars |
Products will be supplied by a source on the Certified List for S-1068 maintained by OMM. Received with TE-24. Check dimension, markings and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain 3 dowel bars and submit for QA testing by the Laboratory. |
|
709.14 |
Epoxy-Coated Steel Wire and Welded Wire Fabric for Reinforcement |
Products will be supplied by a source on the Certified List for S-1068 maintained by OMM. Received with TE-24. Check dimension, markings and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain 3 ft x 3 ft (1 m x 1 m) of the mat and submit for QA testing by the Laboratory. |
|
709.15 |
Plastic Supports for Reinforcing Steel |
Products will be supplied by a source on the Approved List maintained by OMM. Inspect for dimension and condition. |
Notify District Testing if rejecting material that non-performs or looks defective during use. |
|
709.16 |
Galvanizing Steel Option for Bridge Spirals |
Products will be supplied by a source on the Certified List for S-1068 maintained by OMM. Received with TE-24. Check dimension, markings and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain three (3) 30" (.8 m) long samples of each rebar size, with markings, and submit for QA testing by the Laboratory. |
|
710.01.A 710.01 B
|
Barbed Wire
|
Products will be supplied by a source on the Certified List for S-1067 maintained by OMM. Received with TE-24. Check dimension, markings and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain a 5 ft (1.5 m) length of barbed wire and submit for QA testing by the Laboratory. |
|
710.02 |
Woven Steel Wire Fence, Type 47 |
Products will be supplied by a source on the Certified List for S-1067 maintained by OMM. Received with TE-24. Check dimension, markings and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain 4 ft (1.2 m) width of fencing and submit for QA testing by the Laboratory. |
|
710.03 |
Chain-Link Fence [ including Fittings and Accessories] |
Products will be supplied by a source on the Certified List for S-1067 maintained by OMM. Received with TE-24. Check dimension, markings and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain samples as directed by the Laboratory. |
|
710.06 |
Deep Beam Rail
|
Products will be supplied by a source on the Certified List for S-1042 maintained by OMM. Received with TE-24. Check dimension, markings and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain three (3) 1 ft (0.3 m) lengths of guardrail from the same section and submit for QA testing by the Laboratory. |
|
710.09 |
Wire Rope Rail |
Inspect for dimension, condition, appearance and markings on tag or reel. Submit one (1) six (6) ft. sample to OMM. Document in CMS (Trns.port SiteManager ™). |
Approval required prior to use. Notify District Testing and OMM. |
|
710.11 |
Fence Posts and Braces [Lumber] [Steel] |
Products will be supplied by a source on the Certified List for S-1067 and S-1072 maintained by OMM. Received with TE-24. Check dimension, markings and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. |
|
710.12 |
Square-Sawed and Round Guardrail Posts |
Products will be supplied by a source on the Certified List for S-1042 maintained by OMM. Received with TE-24. Check dimension, markings and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. |
|
710.14 |
Pressure Treated Guardrail and Fence Posts, Braces, and Blocks |
Products will be supplied by a source on the Certified List for S-1042 and S-1067 maintained by OMM. Received with TE-24. Check dimension, markings and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. |
|
710.15 |
Steel Guardrail Posts |
Products will be supplied by a source on the Certified List for S-1042 maintained by OMM. Received with TE-24. Check dimension, markings and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. |
|
710.16 |
Guard Posts |
Products will be supplied by a source on the Certified List for S-1042 and S-1067 maintained by OMM. Received with TE-24. Check dimension, markings and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. |
|
711.01 711.04 711.07 |
Structural Steel Cold Rolled Steel Steel Castings |
Material supplied by a Fabricator source on the Certified List for Items 513, 516, 517 & 518 maintained by OMM. Structural Steel Members are received with TE-24. |
If questions concerning structural steel materials, contact OMM Structural Steel Section and notify District Testing. |
|
711.02
|
Galvanized Steel |
Any material supplied with galvanizing will conform to this specification. Randomly inspect galvanizing for appearance and thickness of coating.
|
Notify District Testing if rejecting material.
|
|
711.03
|
Steel for Sheet Piling |
Certified Mill Test Data required for new material. Verify tensile and chemical properties meet requirements. Inspect all material for dimension and condition. Used material is not acceptable for permanent installations. Document field inspection. |
|
|
711.08
|
Arc-welding Electrode & Fluxes |
Verify manufacturer is on Approved List maintained by OMM. Inspect for dimension, condition and markings. Document in CMS (Trns.port SiteManager ™). |
If material is not on Approved List, certification and test data from supplier will be submitted to OMM. Do not use until approval has been received. |
|
711.09
|
High Strength Bolts Nuts and Washers |
Received with TE-24. Inspect material for dimension, condition and markings. Reject defective material. Perform field testing of assembly combination per S-1080. Document field inspection & testing in CMS (Trns.port SiteManager ™ ). |
If field test does not meet requirements of S 1080, retest bolt, nut and washer combination after application of a lubricant. Notify District Testing if rejecting material. |
|
711.10
|
Machine Bolts |
General specification for many common bolts Verify material is component of certified supplier shipment like S-1042 for Guardrail Suppliers or S-1067 for Fence Suppliers. Inspect for condition and coating. Reject defective material. |
Notify District Testing if rejecting material.
|
|
711.12 711.13 711.14 |
Gray Iron Castings Ductile Iron Castings Gray Iron & Ductile Iron Castings |
Verify manufacturer is on Approved List maintained by OMM. Received with TE-24. Inspect for condition and defect. |
Notify District Testing if rejecting material |
|
711.15 711.16 711.17 711.18 711.19 |
Sheet Copper Phosphor Bronze Plate Cast Bronze Leaded Bronze Sheet Lead |
Material supplied by a Fabricator source on the Certified List for Items 513, 516, 517 & 518 maintained by OMM. Structural Steel Members are received with TE-24. Document in CMS (Trns.port SiteManager ™). |
If questions concerning structural steel materials, contact OMM Structural Steel Section and notify District Testing. |
|
711.20 |
Aluminum for Railings |
Material supplied by a Fabricator source on the Certified List for Items 513, 516, 517 & 518 maintained by OMM. Structural Steel Members are received with TE-24. Document in CMS (Trns.port SiteManager ™). |
If questions concerning structural steel materials, contact OMM Structural Steel Section and notify District Testing. |
|
711.21 |
Preformed Bearing Pads |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition and defect. Verify dimension conform to plan requirements. Document in CMS (Trns.port SiteManager ™). |
If material non-performs or looks defective during use notify District Testing and OMM. |
|
711.23
|
Elastomeric Bearings |
Only accept elastomeric bearings shipped by TE-24.and provided by certified suppliers conforming to S1081. Notify district testing. to Inspect material to check location and number of internal shims utilizing an ice pick or similar tool. Five (5) Durometer Gage readings should be taken and averaged to determine compliance with design plans. Document in CMS (Trns.port SiteManager ™). |
Field acceptable for durometer. Reading average range: +/- 7 points of design plan number.
|
|
711.24 |
Waterproofing fabric |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition and defect. Verify dimension conform to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material.
|
|
711.25 |
Type 2 Membrane Waterproofing |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition and defect. Verify dimension conform to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use send one (1) 4 ft2 sample representative of defect to OMM for QA follow-up. |
|
711.26 |
Structural Timber, Lumber and Piling |
Products will be supplied by a source on the Certified List for S-1072 maintained by OMM. Received with TE-24 and supplier bill of lading. Check dimension, quantity and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use.
|
|
711.27
|
Prestressing Steel |
Material supplied by a Fabricator source on the Certified List for Items 515 maintained by OMM. Prestressed Concrete Members are received with TE-24. |
If questions concerning prstressed concrete or prestressed |
|
711.28 |
Cellular Polyvinyl Chloride Sponge |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition and defect. Verify dimension conform to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use send one (1) 1.5'x2.5' sample representative of defect to OMM for QA follow-up. |
|
711.29 |
Type 3 Membrane Waterproofing |
Verify type and brand name of material is on QPL at the time of use. Membrane primer is 705.04 material Inspect for condition and defect. Verify dimension conform to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use send one (1) 4 square ft sample representative of defect to OMM for QA follow-up. |
|
711.30 |
Aluminum for Steps |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition and defect. Verify dimension conform to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use.
|
|
711.31 |
Reinforced Propylene Plastic Manhole Steps |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition and defect. Verify dimension conform to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use.
|
|
712.01 |
Expansion Shield Anchors |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition and defect. Verify dimension conform to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain three(3) samples representative of defect to OMM for QA follow-up. |
|
712.02 |
Calcium Chloride
|
Verify type and brand name of material is on QPL at the time of use. Inspect for condition and defect. Verify dimension conform to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use contact OMM. |
|
712.03 |
Sodium Chloride |
Inspect material for condition. Submit one (1) pint sample per Each Purchase Order to OMM. Document in CMS (Trns.port SiteManager ™). |
If additional samples required for material quantities exceeding 3000 tons, Notify District Testing. |
|
712.04 A |
Lime [masonry] |
Sample & Inspect material for condition with 24 hrs of receipt. One (1) five (5) lb sample. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material.
|
|
712.04 B |
Lime [Quick] for Stabilization |
Assure provided material is from suppliers certified under Supplement 1087 and documentation for m S1087 is complete. Document in CMS (Trns.port SiteManager ™). If questions on material quality sample. One (1) ten (10) lb sample of Quicklime. Send to Geotechnical Engineering. |
Notify District Testing if rejecting material. Samples may be taken in triplicate, if required. Contact Geotechnical Engineering. |
|
712.04 C |
Lime Kiln Dust for Stabilization |
Assure provided material is from suppliers certified under Supplement 1087 and documentation for m S1087 is complete. Document in CMS (Trns.port SiteManager ™). If questions on material quality sample. One (1) ten (10) lb sample of Lime Kiln Dust. Send to Geotechnical Engineering |
Notify District Testing if rejecting material. Samples may be taken in triplicate, if required. Contact Geotechnical Engineering. |
|
712.06 |
Preservative Treatment for Structural Timber |
Component material of pressure treated lumber. No approval required. |
If questions on pressure treated lumber check the specific material item and follow those instructions |
|
712.09
|
Geotextile Fabrics
|
Verify type and brand name of material is on QPL at the time of use. Inspect for condition and defect. Verify dimension conform to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use submit one (1) 4' x 4' sample representative of defect to OMM. |
|
712.10 |
Prefabricated Edge Underdrain |
Inspect material for condition and dimension. Manufacturer’s certified test data required for acceptance. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. |
|
712.11
|
Temporary Erosion Control Mats Material [Types A through I] |
Inspect material for condition and dimension. Manufacturer’s certified test data required for acceptance. Field Acceptance item Refer to Temporary Materials Policy for documentation requirements. |
Notify District Testing if rejecting material.
|
|
720.01 |
Rectangular Reflectors |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, color requirements and defect. Verify dimension conform to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM Chemical section, if rejecting material because material non-performs or looks defective during use. |
|
720.03 |
Flexible Delineator Posts |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition and defect. Verify dimension conform to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM Chemical section, if rejecting material because material non-performs or looks defective during use. |
|
720.04 |
Barrier Reflectors |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition and defect. Verify dimension conform to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM Chemical section, if rejecting material because material non-performs or looks defective during use. |
|
721.01 |
Raised Pavement Marker Castings |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition and defect. Verify type conforms to pre-qualification requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain one (1) 4x2x0.48 in. sample representative of defect to OMM for QA follow-up. |
|
721.02 |
Prismatic Retroreflector and Adhesive |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition and defect. Verify type conforms to pre-qualification requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain one (1) sample representative of defective RPM casting to OMM for QA follow-up. |
|
721.03 |
Casting Adhesive |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition and defect. Verify dimension conform to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM Chemical section, if rejecting material because material non-performs or looks defective during use.
|
|
725.02
|
Wire and Cables
|
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, markings and conformance to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use send a sample representative of non -compliance or defect to OMM for QA follow-up. |
|
725.03 |
Unit Type Duct-Cable Systems |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, markings and conformance to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use send a 10 ft. sample representative of non -compliance or defect to OMM for QA follow-up. |
|
725.04 |
Rigid Ferrous Metal Electrical Conduit and Fittings |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition of coating and conformance to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use send a sample representative of non -compliance or defect to OMM for QA follow-up. |
|
725.051 |
Polyvinyl Chloride Conduit and Fittings |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, markings and conformance to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use send a sample representative of non -compliance or defect to OMM for QA follow-up. |
|
725.052 |
Polyethylene Conduit and Fittings |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, markings and conformance to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use send a sample representative of non -compliance or defect to OMM for QA follow-up. |
|
725.06 |
Polymer Concrete Pull Boxes |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, dimension, markings and conformance to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use send a sample representative of non -compliance or defect to OMM for QA follow-up. |
|
725.07 |
Plastic Pull Box |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, dimension, markings and conformance to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
725.08 |
Portland Concrete Pull Boxes |
Products will be supplied by a source on the Certified List for S-1073 maintained by OMM. Received with TE-24. Check dimension, markings, roughness or excessive cracks. Item 604 Installation documented on CA-P-3 Inspection Form. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
725.10 |
Junction Boxes |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, dimension, markings and conformance to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
725.11 B |
Lamps for Luminaires |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, markings and conformance to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
725.11 E |
Luminaires for High Intensity Discharge Lamps (including Optical system, lamp, ballast and housing) |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, dimension, markings and conformance to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
725.11 F |
Wall Mounted Underpass Luminaires (including Optical system, lamp, ballast and housing) |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, dimension, markings and conformance to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
725.11 G |
High Mast/Low Mast Luminaire (including Optical system, lamp, ballast and housing) |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, dimension, markings and conformance to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
725.12 |
Polyethylene, Fiberglas reinforced, Pull Box with Polymer concrete cover and support ring
|
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, dimension, markings and conformance to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
725.15 |
Circuit Cable Connections and terminations |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, dimension, markings and conformance to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
725.16 |
Ground Rods |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, dimension, markings and conformance to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use contact OMM. |
|
725.19 I |
Power Service Components Wood Pole
|
Products will be supplied by a source on the Certified List for S-1072 maintained by OMM. Received with TE-24 and supplier bill of lading. Check dimension, quantity and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use.
|
|
725.20 |
Multiple Cell Polyvinyl Chloride Conduit and Fittings |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, dimension, markings and conformance to plan requirements. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
725.21 A |
Luminaire Supports Light Poles |
Inspect material for condition and conformance to plan requirements. Verify pole provided by Certified Manufacturer under Supplement 1091. Accept with TE-24 Document in CMS (Trns.port SiteManager ™) |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
725.21 B |
Luminaire Supports Light Towers |
Inspect material for condition and conformance to plan requirements. Verify pole provided by Certified Manufacturer under Supplement 1091. Accept with TE-24. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
725.21B9 |
Luminaire Support Anchor Bolts |
OPTION 1 Verify type and brand name of material is on QPL at the time of use. Inspect for condition, and conformance to plan requirements. OPTION 2 Verify pole provided by Certified Manufacturer under Supplement 1091. Accept with TE-24. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.01 |
Steel Tube and Pipe |
This item typically is a component of a sign support. Inspect total component for condition and conformance to shop drawings. Document in CMS (Trns.port SiteManager ™) |
Notify District Testing if rejecting material.
|
|
730.015 |
U-Channel Posts |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District testing and OMM. |
|
730.016 |
Square Posts |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.02 |
Steel Anchor Bolts and Nuts |
OPTION 1 Verify type and brand name of material is on QPL at the time of use. Inspect for condition, and conformance to plan requirements. OPTION 2 Verify pole provided by Certified Manufacturer under Supplement 1093. Accept with TE-24. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.03 |
Steel Poles and Arms |
Component material provided by Certified Manufacturer under Supplement 1093. Verify manufacturer is on 1093. Accept with TE-24. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.04 |
Base and Arm Plates |
Component material provided by Certified Manufacturer under Supplement 1093. Verify manufacturer is on 1093. Accept with TE-24. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.05 |
Handhole Covers |
Component material provided by Certified Manufacturer under Supplement 1093. Verify manufacturer is on 1093. Accept with TE-24. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.06 |
Pole Caps |
Component material provided by Certified Manufacturer under Supplement 1093. Verify manufacturer is on 1093. Accept with TE-24. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.07 |
Arm Caps |
Component material provided by Certified Manufacturer under Supplement 1093. Verify manufacturer is on 1093. Accept with TE-24. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.08 |
Steel Hardware |
Component material provided by Certified Manufacturer under Supplement 1092 or 1093. Verify manufacturer is on 1092 or 1093. Accept with TE-24. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.09 |
Stainless Steel |
Component material provided by Certified Manufacturer under Supplement 1092 or 1093. Verify manufacturer is on 1092 or 1093. Accept with TE-24. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.10 |
Stainless Steel Hardware |
Component material provided by Certified Manufacturer under Supplement 1092 or 1093. Verify manufacturer is on 1092 or 1093 Accept with TE-24. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.11 |
Aluminum Sheet and Plate |
Component material provided by Certified Manufacturer under Supplement 1092 or 1093. Verify manufacturer is on 1092 or 1093. Accept with TE-24. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.12 |
Aluminum Extrusions |
Component material provided by Certified Manufacturer under Supplement 1092 or 1093. Verify manufacturer is on 1092 or 1093. Accept with TE-24. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.13 |
Aluminum Tube and Pipe |
Component material provided by Certified Manufacturer under Supplement 1092 or 1093. Verify manufacturer is on 1092 or 1093. Accept with TE-24. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.14 |
Aluminum Castings |
Component material provided by Certified Manufacturer under Supplement 1092 or 1093. Verify manufacturer is on 1092 or 1093. Accept with TE-24. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.15 |
Aluminum Forgings |
Component material provided by Certified Manufacturer under Supplement 1092 or 1093. Verify manufacturer is on 1092 or 1093. Accept with TE-24. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.16 |
Aluminum Welding Rods |
Normally only applies to shop fabrication. If performing field aluminum welding contact District Testing and OMM for recommendations. |
Notify District Testing if rejecting material.
|
|
730.17 |
Aluminum Hardware |
Component material provided by Certified Manufacturer under Supplement 1092. Verify manufacturer is on 1092. Accept with TE-24. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.18 |
Reflective Sheeting Type F |
Use if certification provided. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.19 |
Reflective Sheeting Type G |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.191 |
Reflective Sheeting Type G reboundable |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.192 |
Reflective Sheeting Type H
|
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.193 |
Reflective Sheeting Type J |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.20 |
Nonreflective Sheeting |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
730.22 |
Silk Screen Inks |
No field acceptance requirements.- part of 730.19,191,192 or 193 items. |
|
|
730.23 |
Transparent Electronic Cuttable Films |
No field acceptance requirements.- part of 730.19,191,192 or 193 items No field requirements. |
|
|
731.03 |
Changeable Message Sign, Electrical Type |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
731.05 |
Internally Illuminated Fixed Message Sign |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
731.06 |
Sign Flasher Assembly |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
731.07 |
School Speed Limit Sign Assembly |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
731.08 |
Flexible Conduit |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
731.10 |
Timer with Enclosure |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.01
|
Vehicular Signal Heads, Conventional |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.02 |
Vehicular Signal Heads, Optically Programmed, 12-inch (300 mm) Lens |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.03 |
Vehicular Signal Heads, Optically Programmed, 8-inch (200 mm) Lens |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.04 A |
Optically Programmed And Pedestrian Incandescent Signal Lamps |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.04 B |
Vehicular Signal Incandescent Lamps |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.04 C |
Vehicular and pedestrian light Emitting Diode Lamps |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.05 |
Pedestrian Signal Heads [Type A1] [Type A2] [Type D2] |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.06 |
Pedestrian Pushbuttons |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.07 A |
Loop Detector Units Nema TS 1 |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.07 B |
Loop Detector Units Nema TS 2 |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.08 |
Loop Detector Units, Delay and Extension Type |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.09 |
Magnetometer Detector Units |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.10 |
Magnetometer Sensor Probes |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.11 |
Signal Supports |
Check provided by Certified Manufacturer under Supplement 1094 Accept with TE-24. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.12 |
Strain Poles |
Check provided by Certified Manufacturer under Supplement 1094 Accept with TE-24. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.13
|
Wood Poles |
Check provided by Certified Manufacturer under Supplement 1072 Accept with TE-24. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.14
|
Down Guy Assemblies |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.15 |
Pedestals |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.16 |
Conduit Risers |
See 725.04 requirements. |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.17 |
Cable Support Assemblies |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.18 |
Messenger Wire |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.19 |
Cable and Wire |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.20 |
Power Service |
See 725.04 requirements |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
732.21 |
Disconnect Switch with Enclosure |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
733.02 A |
Controller Unit Type TS2/A1 |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
733.02 B |
Controller Unit Type TS2/A2 |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
733.02 C |
Controller Unit Type 170E |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
733.02 D |
Controller Unit Type 2070L and LC |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
733.03 A |
Cabinet Type TS 1 |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
733.03 B |
Cabinet Type TS 2 |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
733.03 C |
Cabinet Type 332 |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
733.03 D |
Cabinet Type 334 |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
733.03 E |
Cabinet Type 336 |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
733.04 A |
Cabinet Riser for TS 1 – TS 2 cabinet |
Field inspect for 1/4 aluminum thickness and accept. |
Notify District Testing if rejecting material.
|
|
733.04 B |
Cabinet Riser for Types 332, 334 or 336 |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
733.05 |
Flasher Controller |
Verify type and brand name of material is on QPL at the time of use. Inspect for conformance to dimension and condition. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
733.06 |
Controller, Master, Traffic Responsive |
Assure the same manufacturer as the supplied controller unit 733.02. |
Notify District Testing if rejecting material. |
|
733.07 |
Remote Monitoring Station |
Compatible with the supplied 733.02 and 733.06 unit. |
Notify District Testing if rejecting material.
|
|
740.02 |
Traffic Paint |
Verify material is on Approved List maintained by OMM. Accepted with TE-24. Inspect container for appropriate markings. Inspect material for uniform consistency. Document in CMS (Trns.port SiteManager ™). |
If rejecting for performance provide 1 qt (1 L) sample and notify District. |
|
740.03 |
Polyester Pavement Marking |
Verify material is on Approved List maintained by OMM. Accepted with TE-24. Inspect container for appropriate markings. Inspect material for uniform consistency. Document in CMS (Trns.port SiteManager ™). |
If rejecting for performance provide 1 qt (1 L) sample and notify District. |
|
740.04 |
Thermoplastic Pavement Marking |
Verify material is on Approved List maintained by OMM. Accepted with TE-24. Inspect container for appropriate markings. Inspect material for uniform consistency. Document in CMS (Trns.port SiteManager ™). |
If rejecting for performance provide 1 qt (1 L) sample and notify District. |
|
740.05 |
Preformed Pavement Marking |
Verify material is on Approved List maintained by OMM. Accepted with TE-24. Inspect container for appropriate markings. Inspect material for uniform consistency. Document in CMS (Trns.port SiteManager ™). |
If rejecting for performance provide 1 qt (1 L) sample and notify District. |
|
740.06 |
Work Zone Pavement Marking [Type 1 Removable] [Type 2 Non-Removable] |
Materials accepted by Engineer. Inspect material for uniform consistency. Document in CMS (Trns.port SiteManager ™). |
If rejecting for performance provide 1 qt (1 L) sample and notify District. |
|
740.07 |
Epoxy Pavement Marking Material |
Verify material is on Approved List maintained by OMM. Accepted with TE-24. Inspect container for appropriate markings. Inspect material for uniform consistency. Document in CMS (Trns.port SiteManager ™). |
If rejecting for performance provide 1 qt (1 L) sample and notify District |
|
740.08 |
Heat-Fused Preformed Plastic Pavement Marking Material |
Verify material is on Approved List maintained by OMM. Accepted with TE-24. Inspect container for appropriate markings. Inspect material for uniform consistency. Document in CMS (Trns.port SiteManager ™). |
If rejecting for performance provide 1 qt (1 L) sample and notify District |
|
740.09 A |
Glass Beads – for 740.02
|
Accepted with TE-24. Inspect container for appropriate markings. Inspect material for uniform consistency. Document in CMS (Trns.port SiteManager ™). |
Accept if accompanied by a TE-24 |
|
740.09 B |
Glass Beads – for 740.03 |
Accepted with TE-24. Inspect container for appropriate markings. Inspect material for uniform consistency. Document in CMS (Trns.port SiteManager ™). |
Accept if accompanied by a TE-24 |
|
740.09 C |
Glass Beads – for 740.04 |
Accepted with TE-24. Inspect container for appropriate markings. Inspect material for uniform consistency. Document in CMS (Trns.port SiteManager ™). |
Accept if accompanied by a TE-24 |
|
740.09 D |
Glass Beads – for 740.07 |
Verify material is on Approved List maintained by OMM. Accepted with TE-24. Inspect container for appropriate markings. Inspect material for uniform consistency. Document in CMS (Trns.port SiteManager ™). |
Accept if accompanied by a TE-24 |
|
748.01 |
Ductile Iron Pipe, Joints, and Fittings |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, dimension, suitability for intended use. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
748.02 |
Polyvinyl Chloride (PVC) Pipe, Joints, and Fittings |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, dimension, suitability for intended use. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
748.03 |
Polyethylene (PE) Service Branches and Fittings |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, dimension, suitability for intended use. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
748.05 |
Copper Service Branches and Fittings |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, dimension, suitability for intended use. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
748.06 |
Steel Pipe Encasement |
Basis of acceptance is certified test data containing documentation of domestic origin from manufacturer. |
Notify District Testing if rejecting material |
|
748.07 |
Polyethylene Encasement |
Verify manufacturer certification conforms to ANSI/AWWA C105/A21.5 Inspect condition, dimension, suitability for intended use. |
Notify District Testing if rejecting material. |
|
748.08 |
Gate Valve and Valve Box |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, dimension, suitability for intended use. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
748.09 |
Inserting Valve and Valve Box |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, dimension, suitability for intended use. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
748.10 |
Cutting-in Sleeve, Valve, and Valve Box |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, dimension, suitability for intended use. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
748.11 |
Tapping Sleeve, Valve, and Valve Box |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, dimension, suitability for intended use. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
748.12 |
Tapping Saddle and Corporation Stop |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, dimension, suitability for intended use. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
748.13 |
Service Stop and Service Box |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, dimension, suitability for intended use. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM. |
|
748.14 |
Meter, Setting, Stop, and Chamber |
Inspect for condition, dimension, suitability for intended use. Acceptance based on manufacturer’s statement of conformity. |
|
|
748.15 |
Fire Hydrant |
Verify type and brand name of material is on QPL at the time of use. Inspect for condition, dimension, suitability for intended use. Document in CMS (Trns.port SiteManager ™). |
Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM.
|
|